Seat Belt Hardware

Use to mount seat belt retractor or hard sleeve female end in floor mount applications. Included with 3 point and 2 point hardware kits.
Price includes 1 piece. The width is 1¼" and one side is 2" long and the other is 1¾" long.

This 6" extension bracket is necessary for driver side high middle console applications (as with Jeep Wranglers and others) or with any application where extra length is needed. The 6" extension bracket brings the buckle of the seat belt up higher so that it clears the high middle console. Click Here to view how it attaches to the seat belt end. This includes 1 bracket only (no bolts, washers etc.)

This 6 inch extension angle bracket is the same as above, but it is for the passenger side seat belt. Needed for high middle console applications (as with some Jeep Cherokee, Wranglers and others). Brings the buckle of the seat belt higher so that it clears the higher middle console. Click Here to see attachment. Includes 1 bracket only (no bolts, washers etc.)

These are our bucket seat style 11" seat belt plastic sleeves, that include the sleeve only (no seat belt). Round cap pops on and off for tightening hex bolt on seat belt end. Price includes 1 sleeve.

Available in Black, Navy Blue, Charcoal, Lt Grey and Tan. Click Here to see side view!

Includes 2ea. 7/16" SAE fine thread 1½" long grade 5 bolts, nuts with lock washers (or lock nuts), 2ea. large fender washers for easy seat belt installation.

Includes 2ea. 7/16" SAE fine thread 1½" long grade 5 bolts, nuts with lock washers (or lock nuts), and 2 flat washers for easy installation.

This 2 point retractable seat belt hardware kit includes all the hardware that you'll need to install one of our retractable lap belts.

2 Long SAE Fine Thread Bolts with nuts and lock washers

2 Short SAE Fine Thread Bolts with nuts and lock washers

2 Large Fender Washers

2 90 degree Angle Brackets

All Bolts Exceed Grade 5 Rating

Hardware kit includes 1 Angle Bracket, 2ea. 7/16" SAE fine thread GRADE 5 bolts, nuts and lock washers (or lock nuts), large fender washers. 1 Shoulder Bolt & one 10154 mounting Plate.

This hardware kit is for our aftermarket replacement seat belt for roadsters and back seat applications where the retractor box is installed on the back package shelf or on the side of the vehicle above and behind the back seat. Includes: 2 large fender washers, 1 angle bracket, 3 long bolts and 1 short bolt (SAE 7/16" fine thread) with lock washers and nuts plus 1 #10154 mounting plate. All Bolts Exceed Grade 5 Rating.

Hardware kit includes 2 long and 1 short 7/16" SAE fine thread grade 5 bolts, nuts and lock washers (or lock nuts), 2 large fender washers. 1 Shoulder Bolt, one 90 degree angle bracket & one 10154 Mounting Plate.

Hardware includes 3 each of: 7/16" fine thread grade 5 hex bolts, nuts, lock washers (or lock nuts) and large fender washers.

This Big Rig 3-Point Retractable Seat Belt Hardware Kit includes 2 short 7/16" SAE fine thread grade 5 bolts and lock washers, 1 Shoulder Bolt, and one CA53 Mounting Plate. (Previously part #102) (#10154)
For installation of our retractable semi-truck big-rig 3-point seat belt that's compatible with air-ride seats!

7/16" SAE fine thread. This mounting plate must be used for applications where no factory anchor points have been established. This plate is to be installed on the underside of the floor board or inside the door post. Outside dimensions: 1^3/16" x 3" Price includes 1 piece.

How to Retrofit 3-point Seat Belts Shoulder Bolt Anchor Point

7/16" SAE fine thread and 1½" long. The non-threaded portion located just below the hex bolt head is 9/16" in diameter - Black. Includes 1 piece. Will only fit the shoulder anchor point position for 3 Point passenger car seat belts. Also, NOT for use for racing seat belts / harnesses.

Price includes 1 seatbelt extender.
Go to our Seat Belt Extender Main Page to see detailed installation seatbelt extensions instructions and belt extenders colors and more new info! We have 3 seatbelt extenders colors.

Easily snaps onto an eye bolt. Want to see? Click Here

Price includes 1 each: 7/16" SAE fine thread eye bolt (threaded portion is 1-3/4" long), nut and large fender washer.

These harness bolt tabs can be used with either 2" or 3" webbing (belts). Price includes 1 piece.
Important: These are to be used with racing and off-road harnesses Only (Not for passenger car seat belts).

This 2" harness slide bar is to be used with 2" webbing (belts). Price includes 1 piece.
Important: This item is to be used with racing and off-road harnesses Only (Not for passenger car seat belts).

This Pyrotect 3 inch harness slide bar is to be used with 3 inch wide webbing (belts). One piece is included with price.
Important: This item is to be used with racing and off-road harnesses Only (Not