Industrial Seat Belt / Military Seat Belts

These lap seat belts are 3" wide belts that are adjustable and available in 5 different lengths. Your choice of 60 inch, 74 inch, 90 inch, 110 inch or 140 inch length seat belts when fully extended! Meets SAE J386 Standard.

These are the perfect lap seat belt for the mining industry, earth moving equipment or other heavy equipment where regulations require a 3" wide safety restraint. They are heavy duty 3" wide restraints and the chrome lift lever release latch is perfect for operators that are wearing heavy work gloves (no push buttons to make the belt release...just grab and pull). Optional installation #210 hardware kit Click Here to view.
Click to view our Belt Hardware Page.

3 inch wide webbing (belt).

2 point (lap only) lap belt NON-retractable.

Adheres to SAE J386 standard.

Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 approved.

Your choice of 60 inch, 74 inch, 90 inch, 110 inch and 140 inch lengths!

Easy and quick release even when wearing gloves.

Optional Choice for Snap End Type End Type What's That?

Available in BLACK ONLY

Click Here to view installation instructions! Click to See Dimensions!

These safety restraint belts are Safety tested and approved, assembled, sewn and packaged in the USA.

Closed Loop Adjustable Belt

Brushed metal buckle with push-button release.

These restraints are NOT to be bolted into a vehicle.

Sizes: belt maximum length of 60, 74, 90 or 110 inches fully adjustable. Now also 48".

30 colors to choose from, 6 Standard and 24 Custom colors. Custom colors are made to order and are not returnable.

meets Society of Automotive Engineers (SAE) J386 specs and Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 Safety Approved Belts

Price includes 1 adjustable restraint.

Retractable Tractor Seat Belt 6" Micro-Switch End - Both Circuit Closed and Open

This tractor seat belt is BOTH "Circuit Open" and "Circuit Closed".

Wiring Diagram and Instructions show you how to easily wire the belt for either open or closed!

These 2" wide belts are retractable and have a 3-wire micro-switch that makes sure that the driver buckles up before driving the tractor.

Your choice of either 6 inch, 9 inch or 12 inch long buckle end. Click to See!

Circuit Open: means that the seat belt must be buckled up before the motor will start, preventing drivers from moving the vehicle until they are buckled up.
Or
Circuit Closed: means that if the seat belt is not buckled when the motor is started, then a bell/buzzer can sound alerting that the driver isn't buckled up.

These forklift seat belts work with 12V & 24V Systems.

These are 2-point lap belt only (no shoulder strap) retractable belts. Available in the colors Black and Orange. Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 Approved and meets Society of Automotive Engineers (SAE) J386 specs.

Webbing (belt) Extends 41-43 inches out of the retractor unit. Add the length of the female buckle end for the Total length from mounting hole to mounting hole.

(The optional mounting hardware includes our 210 hardware kit) Click to View.

Micro-Switch Forklift Tractor Non-Retractable Seat Belt "Circuit Closed" and "Circuit Open"

These 2" wide belts are Non-Retractable and the micro-switch makes sure that your forklift driver buckles up before driving the lift. Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 Approved and meets Society of Automotive Engineers (SAE) J386 specs. These are 2-point lap belt only (no shoulder strap) Non-Retractable belts that extend to 74 inches. Belt available in Black or Orange.

Your choice of either 6 inch, 9 inch or 12 inch long buckle end. Click to See!

This forklift seat belt is BOTH "Circuit Closed" and "Circuit Open."

Wiring Diagram and Instructions showing how to easily wire for either open or closed.

Circuit Closed: means that if the seat belt is not buckled when the motor is started, then a bell/buzzer can sound alerting that the driver isn't buckled up. Replaces i-1402-circuit-closed.
Or
Circuit Open: means that the seat belt must be buckled up before the motor will start, preventing drivers from moving the vehicle until they are buckled up.

These fork truck seat belts work with 12 volt & 24 volt Systems.

Optional mounting hardware kit Click to View. Click to view our Belt Hardware Page.

These easy to install seat belts are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 approved push button lap belts. Also meets Society of Automotive Engineers (SAE) J386 specs. Safety tested and approved, sewn, assembled, packaged in the USA. You can choose from 6 different belt lengths.

2 point push button seat belt that adjust to a maximum of 60, 74, 90 110 or 140 inches total length. Now also 48"

60" belt female buckle side: 23 inches
74" belt female buckle side: 32 inches
90" belt female buckle side: 42 inches
110" belt female buckle side: 36 inches
140" belt female buckle side: 46 inches
48" belt female buckle side: 20 inches
These seatbelts are 1-7/8" wide webbing (strap) non-retractable lap belts only (no shoulder harness). They are universal fit so they will work with many applications. New state amusement park laws (for example California) require parks to install amusement ride seat belts for each ride. Our 48" 60" or 74" LB belt is a great choice.

Optional # 212 mounting hardware kit for floor mount applications or our # 210 mounting kit for mounting to the seat frame. Important: Mounting seat belts to the seat frame should only be done when the seat frame is designed to withstand the additional load!

Each optional hardware kit includes all the hardware that you need for 1 person, for one seat. With black, red, gray, tan, maroon and navy colors, the plastic portion of the buckle color matches the color of the webbing (strap). Click to view our Belt Hardware Page. *Important Note: These Made in USA seat belts are Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 approved.
These restraints have not been tested by existing amusement park safety organizations and therefore not approved by any amusement park safety regulatory organizations. Wesco Performance Inc. makes no representation as to the product's ability to protect the user from injury or death when used for an amusement ride restraint. The buyer assumes that risk. The effectiveness of this equipment is directly related to the manner in which it is installed, used, and/or maintained. Proper installation is solely the responsibility of the installer, and will not be assumed by Wesco Performance Inc.
Click Here to see installation instructions!

Retractable Tractor Seat Belt (ALR 5" Short Housing Belt)

These are 2 point retractable push button seatbelts, lap belt with buckle only (no shoulder harness). These are universal fit, so they are perfect for most any tractor. They extend to 53" and of course are Federally approved! This is our Short Housing restraint, meaning that it is best used with a low seat configuration. With higher seat applications, choose our Long Housing seatbelt below.

Sewn, assembled, packaged, safety tested and approved in the USA.

Choice of: 8" or 11" Rigid Sleeve End for High or Low Bucket Seats. Or Choose 20" Bench Seat Floppy End.

Optional mounting hardware kit Click to View. Click to view our SeatBelt Hardware Page. Colors Click to view our 2 Point Belt Installation Guide!

8" Long Housing Retractable Tractor Seat Belts

Best used with a higher seat application, this is a 2 point retractable lap belt with buckle only (no shoulder harness). These are universal fit, so they are perfect for most tractors. They extend to 53" out of retractor and of course these seat belts are Federally Safety approved!

Choice of: 11" or 8" Rigid Sleeve End for High or Low Bucket Seats. Or Choose 20" Bench Seat Floppy End.

Safety approved and tested, sewn, assembled, packaged in the USA.

Optional mounting hardware kit Click to View. Click to view our Belt Hardware Page. Color Chart Click to view our 2 Point Belt Installation Guide!

This big rig truck seat belt is specifically designed for use with an Air Ride style seat. Seat belts for trucks commonly used in big rigs or for commercial trucks. This is a 3 point seatbelt (lap belt and shoulder harness) for semi truck Air Ride suspension style seat up and down movement. This Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 approved new seatbelt for 18 wheeler heavy trucks can be easily installed using our detailed installation guide with diagrams.

Federally Safety Approved - Safety tested and approved, sewn, assembled, packaged in the USA

New 3 Point Retractable (Lap & Shoulder)

For Air Ride Style Suspension Seat

Detailed Seat Belt Installation Instructions & Diagrams

Dual Sensitive Retractor Design: Both "Vehicle Sensitive" What? and "ELR" Emergency Locking Retractor What's That?

Webbing (belt) extends 135" out of retractor.. "Hey Wesco, your team knows everything! How do I know what the proper fitment length is?" See How to Measure for Seat Belt Fitment Here

See Dimensions

Price includes 1 new seat belt for one seat / passenger.

Will Work for Either Driver or Passenger Seat

12 inch Female Buckle End

It is universal fit, so it is perfect for most trucks.

Optional retrofit hardware kit: Click to View: 1 Shoulder Bolt & 1 Mounting Plate, Three 7/16 Fine Thread Grade 5 Bolts, 3 Lock Washers

For Additional Hardware Click Here

Click for Big Rig Seat Belt Installation Guide!

This is a special 3-point (both lap belt and shoulder restraint) retractable seat belt with an (8 inch long)long sash guide for the conversion van application where the shoulder sash guide anchor attachment is higher (usually attaches above the side window) than a normal passenger car configuration.

This belt has a longer sash guide to lower the shoulder strap so that it aligns properly with the occupant's neck/shoulder.

Seat belts also for your box truck, work van, cargo van, Econoline or club wagon.

Also for retrofitting some early model or vintage cars / Hardtops.

Click for Installation Instructions

Compare the installation instructions to your car, truck or van to confirm that this seat belt is vehicle compatible.

Safety tested and approved, sewn, assembled, packaged in the USA. Safety first!

This restraint extends to 125" out of the retractor. "Hey Wesco Team, how do I know what length seatbelt I need?" See Easy Measuring Instructions Here

It is universal fit, so it is perfect for most any conversion van.

Retracts neatly out of the way when released.

Price includes 1 seat belt for one seat / passenger.

Works for both passenger or driver side, front or back seat.

It features an ELR Retractor. What's That?

30 colors to choose from, 7 Standard and 23 Custom colors.

Choose Bench or Bucket Seat Application.

Choice of: 8" or 11" Rigid Sleeve End for Low or High Bucket Seats.

And of course Federally Safety Approved #302/#209 and meets Society of Automotive Engineers (SAE) J386 specs!

IMPORTANT NOTE: Some colors of seatbelts have a different "C" end than pictured above Click to View Installation Instructions for these restraints.

For high middle consoles (17" or more when measured from floor to top of console), one 6 inch extension bracket # 6-AB is needed for each seat belt installed (front seat). Click Here 6 inch extension bracket needed for center consoles that are higher than 17 inches. to see how it attaches to the seat belt end.
Note: Does NOT have electrical wiring, so they cannot be electrically wired to alarms or airbags.

This is a 3 point seat belt (both lap & across shoulder).

The webbing (belt) extends to 125" out of the retractor. "Hey Wesco, how do I know what the proper fitment length is?" See How to Measure for Seat Belts Here

Safety approved, sewn, assembled, packaged and safety tested in the U.S.A. Don't settle for less!

It is universal fit, so it is perfect for most any standard top car, truck or van.

Click for Installation Instructions

Compare the installation instructions to your car, truck or van to confirm that this seat belt is vehicle compatible.

Retracts neatly out of the way when unbuckled.

Price includes 1 seat belt for one seat / passenger.

Works for both driver or passenger side, front or back seat.

Choose Bench or Bucket Seat Application.

Choice of: 11" or 8" Rigid Sleeve End for High or Low Bucket Seats.

Equipped with ELR Retractor What's That?

30 colors to choose from, 7 Standard and 23 Custom colors.

Federally Safety approved #209 & #302 and meets Society of Automotive Engineers (SAE) J386 specs!

Note: Does NOT have electrical wiring, so they cannot be electrically wired to alarms or airbags.

Retractable seat belts sewn, safety tested and approved, assembled, packaged in the USA. Safety is our Top Priority!

These are Three point belts (both lap and over the shoulder)

Specifically designed for roadsters (convertible cars with little or no back seat).

Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 safety approved and meets SAE J386 specs.

These aftermarket Universal Fit Belts, so certain vehicles, models, years may require modifications/retrofitting. Extends to 113".

They are great for most roadsters and certain 75' 76' 77' 78' 79' Ford Trucks. Certain vehicles, models, years may require modifications/retrofitting.

Install Instructions and Diagrams

Compare the installation instructions to your automobile to confirm that this seat belt is vehicle compatible.

Retracts nicely out of the way when unlatched.

30 colors to choose from, 7 Standard and 23 Custom colors.

Choose either bench or bucket seat application.

Choice of: 11" or 8" Rigid Sleeve End for High or Low Bucket Seats.

Price includes 1 seat belt for one seat / passenger.

Works for both driver or passenger side seat, back or front.

It is equipped with an ELR Retractor. What's That?

These belts are designed to be installed with the retractor unit installed just below the bottom of the window and behind the shoulder.

Note: Does NOT have electrical wiring, so they cannot be electrically wired to alarms or airbags.

This seat belt is a NON-retractable 3 point seat belt (both lap belt and across the shoulder) with a plastic push button buckle. Choose from choice of 3 other buckle styles, DON'T MISS our Genuine Fully Remanufactured GM Brushed Metal Buckle. Click to View It extends to 88" (Choose Bench or Bucket Seat Application). This seatbelt is universal fit, so it is perfect for most any car, truck or van. All seat belts work in both driver or passenger position in your car and includes 1 restraint for 1 seat/person. Our expert staff can answer any questions that you have and of course these belts are safety Federal Motor Vehicle Safety Standards (FMVSS) #209 & #302 Approved and they are approved safety tested, sewn, assembled, packaged in the USA!
Note: With the orange colored seat belts, the buckle ends and all plastic parts are the color black. With black, gray, tan, maroon, red, blue and navy colors of seatbelts, push button style buckles, stitching and plastic belt loops of the restraint matches the color of the webbing (belt).

For high middle console applications (17" or more when measured from floor to top of console. Example: Jeep Wranglers) one 6 inch extension bracket (# 6-AB) is needed for each seat belt installed. Click on our Belt Hardware Page link below to add to shopping cart or to order. Click Here to view the bracket. Click Here to see how it attaches to the seat belt end. Our optional mounting hardware kit includes one shoulder bolt and one 10154 mounting plate, 2 long and 1 short Grade 5 SAE fine thread 7/16" bolts, nuts and lock washers, 2 large fender washers and one 90 degree angle bracket. Click Here to view!
This seat belt previous part # 1126s

Seat Belt need length added (and it's a 3-point) due to bulky safety or military gear?

Perfect for Military and Safety Personnel Wearing Bulky Gear

Adds 12" (1 Foot) of Length to 3 Point Seat Belt

Detailed Installation Instructions Click Here!

Permanent Solution for 3-Point Seatbelts That are Too Short

Includes All Necessary Hardware

Can be Installed in Minutes

Available Colors: Black, Tan & Light Gray

Works with Most Vehicles (Compare Installation Diagrams with Your Application)

This is our 4 point seat belt with a Push-Button style buckle, featuring 2 inch wide Y-shoulder harnesses for both shoulders that extend to 34 inches when fully extended, plus a 36 inch tail strap that anchors to the floor of the vehicle.The lap belt portion extends to 76 inches. Because these restraints have a Y-harness, they have a shoulder strap for both shoulders, so they are referred to as 4 point seat belts even though they have 3 anchor points. These seat belts work for either, driver, passenger or middle positions in your car, truck, van or RV. This seat belt is perfect for the middle position of a bench seat where you would like to have a shoulder harness seat belt or would like to attach a baby seat or child car seat. (Child car seat seat belt.) Price includes 1 restraint. These four point belts are Federal Safety Standard approved #302!

Will NOT work with seats with an integrated headrest.

NOT for use in off-road or racing vehicles!

Click Here to see installation instructions!
Optional hardware includes 3 each of: 7/16" fine thread grade 5 hex bolts, nuts and lock washers (or 3 lock nuts), also three 3" fender washers. Click Here to view!

Chrome Buckle 4 Point Seat Belt

Our 4 point seat belts are universal to all makes and model vehicles and are labeled Federal Safety Standard approved #302! These four point seat belts are perfect for the middle seat position of bench seats providing shoulder harness restraints where none were available before. Although referred to as four point seatbelts because there are 2 shoulder straps using a Y-shoulder harness, they actually have only 3 anchor points. Also great for use of infant car seat in the middle position that require a shoulder harness strap. (Child car seat restraint / harness.) For bucket seat installations, this seatbelt is best used with bucket seats with adjustable headrest (not where headrest and seat are all one piece). Seat belts work in either driver, passenger or middle position in your car, truck or van. Price includes 1 restraint. These floor mount 4 point belts with 2 inch shoulder harness which are retrofit products and are not original manufacturer's equipment. Will NOT work with seats with an integrated headrest.

NOT for use in off-road or racing vehicles!

Click Here to see installation instructions!

Click to view Optional Hardware Kit. Click to see our Hardware Page.

These 4 point seatbelts have a Chrome Lift-Latch style buckle for that retro aviation style look which features 2 inch shoulder harnesses for both shoulders that extend to 34 inches when fully extended, plus a 36 inch tail strap that anchors to the floor of the vehicle.The lap belt portion extends to 76 inches. These seatbelts work for either, driver, passenger or middle seat positions in your car, van, truck or RV. This seat belt is perfect for the middle position of a bench seat where you would like to have a shoulder restraint seatbelt or would like a seat belt to attach a child car seat / baby car seat which requires a shoulder harness seat belt. (child safety harness system)

Pyrotect Racing Lap Belt with Latch and Link Buckle with Bolt-in Ends and 3 inch Webbing (belt) Width.

Features no side belt length adjusters to rub hips. Adjusters are built into the buckle. Adjustable 18" to 64" featuring a rugged lever latch and link quick release buckle and standard pull down tightening strap.

Racing Lap Belt 3 inch width.

Price includes 1 belt for 1 seat.

SFI 16.1 Safety Spec.

Colors: Black, Blue, Red

What are Bolt Ends? Click Here

What are Bolt-in Ends, Wrap-Around and Snap Ends? Compare

Pyrotect Racing Lap Belt with Latch and Link Buckle 3 inch Webbing (belt) Width with Snap-in Ends.

Features no side belt length adjusters to rub hips. Adjusters are built into the buckle. Adjustable 18" to 64" featuring a rugged duckbill latch and link quick release buckle and standard pull down tightening strap.

Racing Lap Belt 3 inch Webbing (belt) Width.

Price includes 1 belt for 1 seat.

SFI 16.1 Safety Spec.

Colors: Black, Blue, Red

What are Snap-in Ends? Click Here

What are Bolt-in Ends, Wrap-Around and Snap Ends? Compare

Pyrotect Racing Lap Belt with Latch and Link Buckle 3 inch Webbing (belt) Width. Lap Seat Belt Restraint with Wrap-Around Ends.

Features no side belt length adjusters to rub hips. Adjusters are built into the buckle. Adjustable 18" to 64" featuring a rugged lever latch and link quick release buckle and standard pull down tightening strap.

Racing Lap Belt 3 inch width.

Price includes 1 belt for 1 seat.

SFI 16.1 Safety Spec.

Colors: Black, Blue, Red

What are Wrap Around Ends? Click Here

What are Bolt-in Ends, Wrap-Around and Snap Ends? Compare